Clevis Pins

SAE Clevis Pins

Jay-Cee Sales and Rivet Inc. offers a large selection of SAE clevis pins. For more information, use the table below.

Nominal Size or Basic Pin Diameter		A		B		C		D	E		F		G	H		J	K		L		Recom- mended Cotter Pin Nominal Size
		Shank Diameter		Head Diameter		Head Height		Head Cham- fer	Hole Diameter		Point Diameter		Pin Length	Head to Center of Hole		End to Center Ref	Head to Edge of hole Ref		Point Length
		Max	Min	Max	Min	Max	Min	±0.01	Max	Min	Max	Min	Basic	Max	Min	Basic	Max	Min	Max	Min
3/16	0.188	0.186	0.181	0.320	0.300	0.070	0.050	0.020	0.088	0.073	0.15	0.14	0.58	0.504	0.484	0.09	0.548	0.520	0.055	0.035	1/16	0.062
1/4	0.250	0.248	0.243	0.380	0.360	0.100	0.080	0.030	0.088	0.073	0.21	0.20	0.77	0.692	0.872	0.09	0.736	0.708	0.055	0.035	1/16	0.062
5/16	0.312	0.311	0.306	0.440	0.420	0.100	0.080	0.030	0.119	0.104	0.26	0.25	0.94	0.832	0.812	0.12	0.892	0.864	0.071	0.049	3/32	0.093
3/8	0.375	0.373	0.368	0.510	0.490	0.130	0.110	0.030	0.119	0.104	0.33	0.32	1.06	0.958	0.938	0.12	1.018	0.990	0.071	0.049	3/32	0.093
7/16	0.438	0.436	0.431	0.570	0.550	0.160	0.140	0.040	0.119	0.104	0.39	0.38	1.19	1.082	1.062	0.12	1.142	1.114	0.071	0.049	3/32	0.093
1/2	0.500	0.496	0.491	0.630	0.610	0.160	0.140	0.040	0.151	0.136	0.44	0.43	1.36	1.223	1.203	0.15	1.298	1.271	0.089	0.063	1/8	0.125
5/8	0.625	0.621	0.616	0.820	0.800	0.210	0.190	0.060	0.151	0.136	0.56	0.55	1.61	1.473	1.453	0.15	1.548	1.521	0.089	0.063	1/8	0.125
3/4	0.750	0.746	0.741	0.940	0.920	0.260	0.240	0.070	0.182	0.167	0.68	0.67	1.91	1.739	1.719	0.18	1.830	1.802	0.110	0.076	5/32	0.156
7/8	0.875	0.871	0.866	1.040	1.020	0.320	0.300	0.090	0.182	0.167	0.80	0.79	2.16	1.989	1.969	0.18	2.080	2.052	0.110	0.076	5/32	0.156
1	1.000	0.996	0.991	1.190	1.170	0.350	0.330	0.100	0.182	0.167	0.93	0.92	2.41	2.239	2.219	0.18	2.330	2.302	0.110	0.076	5/32	0.156

Lengths tabulated are intended for use with standard clevises, without spacers. Where required, it is recommended that other pin lengths be limited, if possible to nominal length increments of 0.06 in.
Basic "J" dimension (distance from centerline of hole to end of pin) is specified for calculating hole location from underside of head on pins of lengths not tabulated.
Reference dimension provided for convenience in design layout and is not subject to inspection.

Note: Not responsible for errors

in data tables. Please check with our sales department to confirm specs.